Window and Door Fabrication
Casement, sliding, tilt and turn, slide and fold and vertical sliding units cut, assembled, gasketed and glazed to the measured opening rather than to a stock size.
In-House Workshop, Ghaziabad
Aluminium Fabrication
Cutting, machining, assembly, gasketing and glazing carried out in our own workshop, then installed by our own team. Windows, doors, facades, railings, partitions, gates, cladding and shower enclosures fabricated to the measured opening across Delhi NCR.
- 9 Fabrication Services
- Fabricated to Drawing
- In-House Installation
- Free Site Measurement
Alurac Windoz
5,000+Residences enhanced with Alurac systems
300+Commercial projects completed
1,000+Happy clients, architects & builders
9Fabrication services offered
What Is Aluminium Fabrication?
Aluminium fabrication is the work that turns extruded sections into a finished assembly. It covers reading a drawing into a cutting list, cutting and machining the sections, squaring and joining the frame, seating the gaskets, fitting hardware, glazing, then checking and packing the unit before it leaves the workshop.
Alurac carries out that work in house at Ghaziabad for windows and doors, facades and curtain walls, railings, partitions, gates and cladding, shower enclosures, ACP and HPL elevations, automatic doors and custom details fabricated to a customer drawing. Supply and installation reach Ghaziabad, Noida, Delhi, Gurugram, Faridabad, Meerut and the districts around them. To discuss a job, call +91-9312500138 or email info@alurac.in.
Where Quality Is Actually Decided
Fabrication Is Where a Profile Becomes a Product
Buyers spend a long time comparing systems and glass, and almost no time on who is going to cut and assemble them. That is the wrong emphasis. A premium section assembled badly performs worse than a modest section assembled properly, because every claim a system makes depends on the frame being square and the gaskets being continuous.
Nothing about that is visible once a unit is glazed and installed. An out of square frame, a gasket stopped short at a corner, a drainage slot blocked with swarf: each of them looks identical to good work on delivery day and shows up a season or two later as a draught, a leak or a shutter that will not close.
- Cutting lists worked back from the measured opening, not the builder drawing.
- Diagonals checked for square before the unit is glazed.
- Gaskets run unbroken, including into and around every corner.
- Drainage paths left clear of swarf, sealant and packing.
- Hardware aligned to its keeps rather than forced into position.
What We Fabricate
Aluminium Fabrication Services
Nine fabrication streams covering fenestration, facade, interiors and entrances, all run through the same workshop and the same checks.
Facade and Curtain Wall Fabrication
Mullion and transom assemblies for unitized, semi-unitized, curtain wall and spider glazing, fabricated against the facade drawing and the span it has to carry.
Railing Fabrication
Balcony, staircase and terrace railings cut and assembled around the glass thickness and handrail load, with clamps and base channels aligned before dispatch.
Partition Fabrication
Slim and glass partition assemblies for cabins, meeting rooms and studies, where sightlines have to stay consistent across a whole floor plate.
Gate and Cladding Fabrication
Main gates, front elevations and feature walls built from louvre, batten and box sections, with the repeat rhythm set out before cutting begins.
Shower Enclosure Fabrication
Framed, semi-frameless and sliding enclosures fabricated to the tiled opening, with wall channels and headers set true against an uneven wet-area wall.
ACP and HPL Cladding Fabrication
Panel cutting, grooving, folding and cassette forming with the sub-frame fabricated alongside, so panel lines stay true across a long elevation.
Automatic Door Fabrication
Track beams, carrier rails and glazed leaves assembled and aligned so the drive unit and sensors work against a frame that is genuinely square.
Custom Fabrication to Drawing
Your own detail, reviewed for buildability and then fabricated against the approved drawing, with the cutting list confirmed before anything is cut.
The Workshop Process
How an Aluminium Fabrication Job Runs
Four stages, each of which decides something that cannot be corrected later.
1. Drawing and Cutting List
Every job starts as a cutting list worked back from the measured opening. Errors caught here cost nothing, while the same error caught at assembly wastes material.
2. Cutting and Machining
Sections are cut to length and angle, then machined for drainage, screw ports and hardware. Square, clean cuts are what let a frame close up tight at assembly.
3. Assembly and Glazing
Frames are squared and joined, gaskets seated along their full run, beads fitted and glass installed with the correct packing so the weight sits where it should.
4. Quality Check and Packing
Diagonals, operation, sealing and finish are checked before anything leaves. Units are then interleaved and wrapped so coated surfaces arrive unmarked.
Quality Markers
What Separates Good Aluminium Fabrication From Cheap Work
Six checks that are invisible on delivery day and decisive two seasons later.
Square Corners That Stay Square
A frame assembled out of square will never close evenly, and no amount of adjustment on site corrects it. Diagonals are checked before the unit is glazed.
Clean, Accurate Cuts
A rough or out of angle cut leaves a gap at the joint. That gap is where water, dust and air get in long after the sealant around it has aged.
Gaskets Seated Along Their Full Run
Gasket that is stretched, pinched or stopped short at a corner leaves a path straight through the frame, and it is invisible once the bead is on.
Drainage Left Clear
Drainage slots blocked by swarf, sealant or packing turn a working frame into one that holds water. This is among the commonest fabrication faults in the field.
Hardware Aligned, Not Forced
Locks, stays and rollers should meet their keeps without being bent into place. Hardware forced at assembly is hardware that fails within a few seasons.
Finish Protected Throughout
Coated and anodised surfaces mark easily during handling. Protective film, clean benches and correct packing matter as much as the coating itself.
Who We Work With
Who We Fabricate For
From a single replacement opening to a phased project supply.
Builders and Developers
Project quantities fabricated and dispatched in phases against the construction programme rather than arriving all at once.
Architects and Consultants
Buildability review at detail stage, so a drawn junction is one that can actually be cut, assembled and sealed.
Dealers and Distributors
Fabricated units supplied ready to install, for dealers who sell and fit but do not run a workshop of their own.
Interior Fit-Out Contractors
Partition, cabin and enclosure assemblies fabricated to a floor plate drawing and delivered to suit a fit-out sequence.
Facade Contractors
Mullion, transom and sub-frame assemblies fabricated against the facade package and the loads it has to carry.
Homeowners and Renovators
Single openings and whole-house replacements handled with the same measurement and assembly process as a project order.
Service Area
Aluminium Fabrication and Installation Across Delhi NCR
Our workshop serves these areas and the districts around them.
- Ghaziabad
- Noida
- Greater Noida
- Delhi
- Gurugram
- Faridabad
- Meerut
- Sonipat
- Bahadurgarh
- Hapur
- Bulandshahr
- Modinagar
- Muradnagar
- Loni
- Sahibabad
- Vaishali
- Indirapuram
- Dadri
Outside this area? Project quantities are supplied more widely. Just tell us your location and we will confirm what is workable.
How We Work
From Enquiry to Fitted Door in Five Steps
The same process whether it is one opening or a phased project supply.
01
Book a Consultation
Call, WhatsApp or send an enquiry and we schedule a convenient slot.
02
Share Your Opening
Openings are measured on site and your priorities are noted.
03
Specification & Quote
System, glass, finish and hardware are proposed with an itemised quotation.
04
Fabrication & Fitting
Made to the measured opening, then fitted, sealed and finished by our own team.
05
Showroom Visit
See and operate the systems in person at our Ghaziabad experience centre.
Questions Answered
Aluminium Fabrication: FAQs
What builders, architects and homeowners ask most before placing work.
What is aluminium fabrication?
Aluminium fabrication is the work that turns extruded aluminium sections into a finished assembly. It covers reading the drawing into a cutting list, cutting and machining the sections, assembling and squaring the frame, seating the gaskets, fitting hardware and glazing, then checking and packing the unit before dispatch.
What does Alurac fabricate?
Windows and doors, facade and curtain wall assemblies, railings, slim and glass partitions, gates and cladding, shower enclosures, ACP and HPL cladding with its sub-frame, automatic door assemblies, and custom work fabricated against a customer drawing.
Where does Alurac provide aluminium fabrication services?
Fabrication is carried out at our facility on Grand Trunk Road, Bulandshahr Road Industrial Area, Ghaziabad, serving Ghaziabad, Noida, Greater Noida, Delhi, Gurugram, Faridabad, Meerut and the surrounding districts, with project supply reaching the wider region.
Do you fabricate against our own drawings?
Yes. Share the detail or section drawing and it is reviewed for buildability first, so any junction that cannot be cut, assembled or sealed properly is identified before fabrication rather than during it. The cutting list is then confirmed against the approved drawing.
What makes one fabricator better than another?
In aluminium fabrication it is mostly the things you cannot see once the unit is assembled: whether the frame is genuinely square, whether cuts are clean and on angle, whether gaskets run unbroken into the corners, whether drainage is left clear and whether hardware meets its keeps without being forced.
Do you supply fabricated units or only the sections?
Both. Profiles can be supplied as sections for a fabricator to work with, or we fabricate complete units ready to install. Dealers who sell and fit but do not run a workshop usually take the fabricated option.
Do you install what you fabricate?
Yes. Site survey, measurement, fabrication, installation, sealing and finishing are handled by our own team, which means one point of accountability instead of a fabricator, a glazier and a labour contractor pointing at each other.
How long does fabrication take?
It depends on the quantity, the system and the glass specification. Fabrication and dispatch dates are confirmed in writing when the order is booked so site work can be scheduled around them rather than waiting on them.
Can you fabricate for a phased construction programme?
Yes. Project quantities are commonly fabricated and dispatched in phases to match the construction sequence, which avoids finished units sitting on a live site collecting damage before they can be installed.
Do you handle small jobs as well as projects?
Yes. A single opening is measured, fabricated and fitted through the same process as a project order. The scale changes, the measurement and assembly standard does not.
Have a Drawing or an Opening to Fabricate?
Share your drawings, opening sizes or a few site photos. We will review buildability, confirm the cutting list and share an itemised quotation with fabrication and installation listed separately.
Explore More
Related Pages
The systems and profiles we fabricate with.